一、工藝流程

　　a)吊頂保溫安裝工藝：排版--龍骨安裝--保溫板就位固定--調整--細部處理。

　　b)排版：根椐施工圖紙及實際結構確定吊頂板排版。

　　c)龍骨安裝：采用￠12鍍鋅吊桿作為吊筋，40*80*2mm鍍鋅方管作為主龍骨，間距1.8m(根據實際檁條預留孔調整)，40*60*1.5mm鍍鋅方管作為次龍骨，間距1.78m~3.5m(參照檁條間距)，龍骨連接處焊接。

　　d)保溫板就位固定：將保溫板提升至安裝高度，將保溫板就位找正找平后采用自攻釘將板固定于龍骨上。然后安裝下一張頂板，用緊線器打緊兩張板，確保板與板之間結合緊密，依次安裝，直至頂板安裝完畢，并進行相關洞口的開口。

　　e)調整：板安裝完畢后，進行調平。

　　f)細部處理：頂庫板全部安裝完成后，對板板接縫要進行打膠處理，其他預留縫隙采用聚氨酯發泡進行填滿，吊頂下部邊縫采用圓弧鋁進行收邊，中縫采用平板鋁合金進行收邊。上部縫隙不進行收邊處理，處理完畢后再進行整體清潔。

　　二、連接點處理考慮到使用過程中可能出現的正負風壓問題，我方采用以下方式進行解決:

　　a)在主龍骨吊桿上加裝剛性支撐，以屋面檁條為參照，每隔一道屋面檁條在相應的主龍骨吊桿上加裝剛性支撐，共十道，其中靠兩邊四道為剛性套管(3.2*2.5套管)，剛性支撐間距為3.6m，考慮到鋼管長細比限制，中間六道采用方管現場制作，每個剛性支采用兩道40*60*1.5mm鍍鋅方管連接并與上部屋面檁條用自攻絲連接，剛性支撐間距為3.6m。

　　b)周圈龍骨與墻體之間采取半剛性支撐，采用50mm款(50)角鐵件一端與墻體固定，一端截面上開孔(孔尺寸為12mm*36mm)并與周圈龍骨連接，之間預留20~30mm縫隙作為活動量。